How to install a pull chain switch

How can you install a pull chain or other on off switch on a hardwired fixture to replace a wall light fixture that has not wall switch? How do you install a pull chain switch in a fluorescent light fixture?

How do you wire a fixture that had two hot and two neutral wires? Why does your ceiling fan light fixture flicker when off? How do you replace the turn signal switch on a impala? What is a key less light fixture? Can a single pole switch replace a starter in fluorescent lamps?

Can you replace an old no ground single switch with a three way switch? How do you wire a volts light? Can you connect a wall switch and a light fixture to an existing light fixture? How to replace air vent switch for a Toyota Camry? Can you convert an overhead light fixture that is hardwired into a plug-in fixture? How do you install a brake light switch in a GMC Sierra? Can a single pole switch replace a starter in a tube light? How do i replace a sonata power window switch?

Fuel cut off switch 92 bronco? How do you wire a switch to an electrical fixture? Install fog lights on a Nissan Altima do you replace turn signal switch as well? How do you hookup a switch leg from one switch to a second one?

How do you install pull chain switch into existing Fluorescent lamp? How can I switch the light fixtures in my bathroom? How do you replace ignition switch on a silverado? How do you install power window switches for a Corvette?

How do you replace an old light fixture with two sets of black white and ground wires with a new fixture that only has one set of black white and ground wires? Study Guides. Trending Questions. What's the most outdated thing you still use today? Is it better to take a shower in the morning or at night? What scramble words can you make with these letters a i t o r? Is it illegal to destroy other people's mail? Still have questions? Find more answers. Previously Viewed. How can you install a pull chain or other on-off switch on a hardwired fixture to replace a wall light fixture that has not wall switch?

Unanswered Questions. Is it advantageous or disadvantageous to use one pipette throughout the dilution process and why? What is the exposition in the story The Maguindanao Pearls? The sketch above shows a component which is stamped out of sheet steel The square in the center is discarded These components are stamped out of a continuous steel coil with a width of 70 cms The s? What is the conflict of the story The Maguindanao Pearls? What Latino American psychologists studies showed cultural bias on intelligence tests?

What do you call a rattle snake on a cold and blustery day? Not one for ther ceiling fan. How do you feel about fluorescent lights? If the fixture is where it could shock someone.. But adding a ground to the fixture is 'OK' as long as you keep it on the fixture. I don't know your setup but it's rare to have a ground problem with fluorescent fixtures. Its not exactly up to code but it's also not unsafe if you put a ground wire to the fixture. A cold water pipe will serve as a ground. One of the leading ground problems is that without a decent ground near the tube they can be slow to start.

The newer electronic ballasts have a higher strike voltage, but is still shows up. Indem Sie weiterhin auf der Website surfen bzw. Mehr erfahren. Small-Space Living. Kitchen and Dining Seating. Living Room and Entryway Seating. Sign In. Join as a Pro. Houzz TV. Houzz Research. Looking for the perfect gift? Send a Houzz Gift Card!

Electrical Wiring. Thank you! Email Save Comment 7. Featured Answer. Dean Stewart 6 years ago. Greetings all, I know this is an old thread, however the question still exists and the question needs to be directly answered. Like 1 Save.

Sort by: Oldest. Newest Oldest. Ron Natalie 12 years ago. Well the cheapest solution would be to use CF's in the existing pull chain fixture. Like Save. Related Discussions How do you feel about fluorescent lights? It looks like most people here have a really negative and harsh opinion of fluorescent lighting in home.

If the question is, "how do I wire a switch to an existing light fixture that has no external switch", the answer is, "in series". The attached web site gives simple instructions on how to wire a basic light switch to an existing light.

See sources and related links below. The pull chain on the porcelain light fixture can be converted to a wall switch very easily. You will need to install a new two wire 14 cable from the box the fixture is mounted to now to the new wall switch box. Remove the power to the circuit by shutting that circuit's breaker off.

The wire that is connected to the switch in the light fixture is the incoming "hot" wire. Disconnect it and re connect it to the black wire that goes down to the switch.

Disconnect the white wire from the old porcelain fixture. For the installation of the porcelain fixture connect the white wire to the silver screw on the new fixture. Now connect the white wire that returns from the switch to the brass coloured screw on the new fixture.

Mark this white wire with a small piece of black electrical tape to re identify it as not a neutral code rule but a potential "hot" wire. At the switch end make sure that the black wire is connected to the top screw and the re identified white wire with a black tape marker is connected to the bottom screw of the switch. Connect the ground wire in the cable to the new switch box and the existing fixture box. Install the switch making sure that the switch is in the off position and that the handle in facing downwards.

Install switch plate cover, turn the breaker back on and you are finished. This project is relatively easy to do if there is already an existing wall box close to the pull-chain switch BUT ONLY if it already has the right wiring in it.

If there is no such wall box then a new one will have to be installed and wired. If you already know how to do that safely you would not be asking this question here! For some relevant information, please see the related question below about replacing a wall switch by a pull switch.

As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed. Before you do any work yourself,on electrical circuits, equipment or appliances,always use a test meter to ensure the circuit is, in fact, de-energized. You could turn on the light at pull chain and then install a remote switch in series with the black wire supplying the light. However, if the light is turned off via the pull chain, the remote switch can't turn it back on.

The links are separated by insulating material so there will be no electric shock hazard to a person pulling the chain if the chain happens to contact an energized electric wire.

If the base plate can be removed than a chain ring can be installed with another chain ring installed on the base plate.

Add the chain and wires and you have a pendant lamp. I'd like to install a chain link fence around my property. Are they difficult to install? If you've never done electrical work before, then you should do this with somebody else who has, as a safety precaution. First you need to secure turn off, and mark it so it will not be accidentally turned back on the power to your circuit at the breaker. Test to make sure it is off. Next, install a light receptacle with a pull chain, and then turn the power back on.

With the switch in the 'on' position, test that the chain works as desired. Next, secure power again, then using wire nuts, bypass the wall switch. Then you may remove the wall switch and replace with a blank, if desired. Shut off the power to the light circuit. Remove the old light switch if there is one. Remove the old lamp holder base. Make a diagram and note how the wires were attached, what colour screws to what colour wire. At the light switch wire nut the two wires that came off of the switch together.

The switch plate cover will have to be replaced with a blank cover plate to cover the old switch box. Install the new pull chain lamp holder using the notes and diagram that you made. Some of the lamp holders that have a switch in them will not have terminal screws. The wire to the switch will be the "hot" wire. The other wire from the old lamp holder will be the neutral which should be a white wire. Insert the bulb and turn the power back on. Now the pull chain will control the light rather that the wall switch.

There should be two wires in the box, black and white and possibly a bare one depending on the age of the wiring in the house. The fixture has two screws on the base.